View Lab Report – E2_Lab_2_8_2_instructor from CSTN WAN at Georgian College. Lab Challenge Static Route Configuration (Instructor Version). View Lab Report – E2_Lab_2_8_2 from ARCHUD 30 at University of California, Los Angeles. Lab Challenge Static Route Configuration Topology. Lab Challenge Static Route. Advanced Static Routing Lab – Router Alley. Lab Configuring Static Routes – Instructor Version ·
Author: | Gardagal Kajisar |
Country: | Togo |
Language: | English (Spanish) |
Genre: | Personal Growth |
Published (Last): | 2 June 2016 |
Pages: | 235 |
PDF File Size: | 12.71 Mb |
ePub File Size: | 10.10 Mb |
ISBN: | 622-4-98675-456-4 |
Downloads: | 28288 |
Price: | Free* [*Free Regsitration Required] |
Uploader: | Kajim |
Document the Router Configurations On each router, capture the following command output to a text. Configure an EXEC mode password. Configure a password for VTY connections. Packet Tracer Skills Integration Challenge.
Lab Challenge Static Route Configuration (Instructor Version)
Configure a message-of-the-day banner. Consider the following questions when creating your network design: Assign the last valid host address in subnet 3 to PC1. The summary route will also include the subnet zero route that is reserved for future expansion.
For a review of basic troubleshooting techniques, see Lab 1. Record the command that you used. Page 7 of 7. From PC2, is it possible to ping PC1? List the networks with slash notation. View the routing table of ISP to verify the new static route entry.
Lab Challenge Static Route Configuration – YouTube – tubemate downloader –
Configure an EXEC timeout of 15 minutes. However, you can test connectivity between two routers and between and configuratkon device and its default gateway. Record the command to configure a default static route using the appropriate exit interface. Configure HQ with a default static route.
What networks are present in the HQ routing table?
Configure a password for console connections. Consider 28.2 type of static routing that is needed on ISP. Service provider administrators are human, too, and make mistakes. Therefore, it is important that you understand the types of errors an ISP could make that would cause your networks to lose connectivity. In a real-world implementation of this topology, you would not be configuring the ISP router. View the routing table of HQ to verify the chlalenge static route entries. Record the command you used.
Using the next-hop IP address, configure ISP with a summary static route that includes all of the subnets that are missing from the routing table. Static Routing Lab 2.
Configure the Ethernet interfaces. Cable a network that is similar to the one in the Topology Diagram. Mr S – Dores Community Website. Anawers Static Routing on HQ. If any of the above pings failed, check your physical connections and configurations.
This document is Cisco Public Information. Subnet this network to provide enough IP addresses to support 60 hosts. Answer the following questions to verify that the network is operating as expected: Documents Flashcards Grammar checker.
What networks are present in the ISP routing table? Without testing it first, do you think that PC1 can now successfully ping PC2? Synchronize unsolicited messages and debug output with solicited output and prompts for the console and virtual terminal lines.
You should not have connectivity between end devices yet. Scenario In this lab activity, you will be given a network address that must be subnetted to complete the addressing of the network shown in the Topology Diagram. HQ must be able to send any traffic for which donfiguration does not have a route to ISP.
Lab 2.8.2: Challenge Static Route Configuration – YouTube
Challenge Static Route Configuration 3. Perform Basic Router Configurations. Assign the last valid host address in subnet 1 to PC2. Subnet 0 will be available for future expansion. Assign appropriate addresses to the device interfaces. How many subnets need to be created from the What kind ocnfiguration route would you need to configure on HQ to solve this problem? Assign subnetwork addresses to the Topology Diagram. You can use any current router in your lab as long as it has the required interfaces as shown in the topology.