The European Standard EN has the status of a . ISO (upon which BS EN is based), altering clause 1. Standard [WITHDRAWN] DIN EN Mechanical properties of fasteners; bolts, screws and studs (ISO ); german version EN. Purchase your copy of BS EN , ISO as a PDF download or hard copy directly from the official BSI Shop. All BSI British.
|Published (Last):||5 April 2011|
|PDF File Size:||12.83 Mb|
|ePub File Size:||5.49 Mb|
|Price:||Free* [*Free Regsitration Required]|
It presents the UK view on standards in Europe and at the international level. It defines properties for sizes M1. Figure 8 dn Examples of marking on hexagon socket head cap screws 9.
Mechanical Properties – Steel Screws and Bolts ISO 898-1 EN 20898-1
The length of free thread subjected to the load shall be one diameter 1d. From Wikipedia, the free encyclopedia. Screws threaded to the head shall pass the requirement dln this test if a fracture which causes dni originates in the free length of thread, even if it has extended or spread into the fillet area or the head before separation. If permission is granted, the terms may include royalty payments or a licensing agreement.
Marking of slotted and cross recessed screws is not usual. When carrying out the test, a minimum free threaded length equal to one diameter 1d shall be subjected to the tensile load. If marking on the unthreaded part is not possible, marking of property class only on the nut end of the stud is allowed, see Figure Skip to main content.
It is the constant aim of BSI to improve the quality of our products and services. The standards do not cover fasteners that would otherwise apply but require special properties, such as weldability or corrosion resistance. This European Standard supersedes EN The chemical composition shall be assessed in accordance with the relevant ISO standards. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies.
These normative references are cited at the appropriate places in the text and the publications are listed hereafter. Products in property classes 4. B, Mn or Cr 0,15d 0,40 0, 0, 0, quenched and tempered Carbon steel quenched and tempered 0,25 0,55 0, 0, 9.
In case of doubt, the Vickers hardness test is decisive for acceptance. A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions.
Marking is required for bolts and screws with nominal thread diameters d W 5 mm.
Screws & Bolts – Mechanical Properties
Copyright Copyright subsists in all BSI publications. A hardened wedge in accordance with Table 10 and Table 11 shall be placed under the head of the bolt or screw.
When fasteners are to be used above or below the ambient temperature range it is the responsibility of the user to ensure that the mechanical and physical properties are suitable for his particular service conditions.
Compliance with this standard provides one means of conforming with specific essential requirements of the Directive. Retrieved from ” https: Enter the email address you signed up with and we’ll email you a reset link.
ISO consists of the following parts, under the general title Mechanical properties of fasteners made of carbon steel and alloy steel: Part 5 defines the mechanical properties for set screws and other fasteners not under tensile stresses. Bolts, screws and studs for general requirements.
This part of ISO is applicable to set screws and similar threaded fasteners: It is carried out for the purpose of determining the tensile strength. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.
The test piece shall be taken lengthwise, located as close to the surface of the bolt or screw as possible. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by Februaryand conflicting national standards shall be withdrawn at the latest by February Bolts, screws and studs. Table 15 — Clock-face system for marking bolts and screws Property class 3. Compliance with a British Standard does not of itself confer immunity from legal obligations.
Bolts, screws and studs with specified property classes — Coarse thread and fine pitch thread .
BS EN 20898-1:1992, ISO 898-1:1988
Principles and basic data. Nuts with specified proof load values — Coarse thread . Certain fasteners may not fulfill the tensile or torsional requirements of this part of ISO because of the geometry of the head which reduces the shear area in the head as compared to the stress area in the thread such as countersunk, raised countersunk and cheese heads see clause 6.
In order to meet the requirements of this test, the fracture shall occur in the shank or the free threaded length of the bolt and not at the junction of the head and the shank.
If it is not possible to determine the elongation after 20889 due to the length of the bolt, the reduction of area after fracture shall be measured providing that Lo is at least 3 do. Part 1 does not specify properties for fasteners that have head geometries that reduce the shear strength of the fastener, such as low head screws and countersunk heads.
After mounting, grind and polish the surface in accordance with good metallographic practice. The test applies to bolts and screws with nominal thread diameters d u 3 mm as well as to short bolts and screws with nominal thread diameters 3 mm u d u 10 mm which cannot be subjected to a tensile test.
Click here to sign up. This will be indicated in the amendment table on the inside front dn. This does not preclude the free use, in the course of implementing the standard, of necessary details such as em, and size, type or grade designations. Revisions British Standards are don by amendment or revision.