Engaged Expert Terry Candlish discusses ASTM G and G tests which are used to evaluate sunlight and moisture exposure. ASTM. ASTM G & G UV Testing. The UV testing was performed on ecomère by Touchstone Labs in Tridelphia, WV, again at the request of Southern . ASTM G – Designation: G – 06 Standard Practice for Operating Fluorescent Light Appara.
| Author: | Moogurn Migrel |
| Country: | Pacific Islands |
| Language: | English (Spanish) |
| Genre: | Technology |
| Published (Last): | 13 March 2016 |
| Pages: | 462 |
| PDF File Size: | 3.46 Mb |
| ePub File Size: | 6.15 Mb |
| ISBN: | 442-5-34815-526-5 |
| Downloads: | 38857 |
| Price: | Free* [*Free Regsitration Required] |
| Uploader: | Kazirr |
For instance, a slight shift in formula may produce twice as much resistance to weathering. By blasting a product with UV rays, a weatherometer can simulate exposure results. The more common may be identi? Active view current version of standard. Typically, water vapor shall be generated by heating water and?
Note that glass transmission characteristics will vary due to manufacturer, production lot, thickness, or other factors. Expose replicates of the test specimen and the control specimen so that statistically signi? A number of exposure procedures are listed in an appendix; however, this asrm does not specify the exposure conditions best suited for the material to be tested.
If the aim of testing is to boost color fastness, UV-A bulbs g15-406 ideal. B The data in Table 2 are based on the rectangular integration of 21 spectral power distributions for? The un-insulated thermometers may be made of either steel or aluminum. F For the benchmark daylight spectrum, the UV irradiance to nm is 9.
The lowest wavelength measured shall be no greater than nm.
Cycle 2 has been widely used for coatings. Without testing in a specific location over a number of years, it is impossible to perfectly predict product response. NOTE 9—Typically, these devices control by black panel temperature only. Such outcomes cannot be quickly obtained in outdoor settings; therefore, these weatherization tests are invaluable in timely product development.
Ultimately, the most realistic way to test for weathering is to allow the product to degrade in real time, with outdoor testing panels. A number in parentheses indicates the year of last reapproval. These conditions are provided for reference only See Table X2.
ASTM G154 and G155 Explained
The previous set points were 0. Other lamps, or combinations of lamps, may be used. Element can provide you with critically important data on your product or part’s performance in response to typical or extreme environmental stresses and conditions. These exposures may include a means to introduce moisture to the test specimen. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters.
If the actual operating conditions g1154-06 not agree with the machine settings after the equipment has stabilized, discontinue the test and correct the cause of the disagreement before continuing. Misleading results may be obtained by this method, since the masked portion of the specimen is still exposed to temperature and humidity that in many cases will affect results.
In this standard, the terms UV light and UV radiation are used interchangeably. However, there is no simple equation for calculating exposure. Following are some representative exposure conditions. Generally, two controls are recommended: The lamps shown in this section are representative of their type.
However, each of these g1540-6 brings uniquely inaccurate results. We provide Xenon Arc testing, Carbon Arc testing and UV Exposure testing to simulate exposure of your products or materials to ultraviolet radiation, temperature and moisture.
Consequently, in testers without feed-back-loop control of irradiance, the lamp output will decrease with increasing chamber temperature. This may lead to anomalous results. Cracking, peeling, de-glossing, f154-06, and tensile weakening are additional outcomes of exposure; sometimes such deterioration can even occur through window glass.
When rays of sunlight—particularly UV rays—bombard a surface, they degrade smaller pigment particles, changing the surface color and creating a chalky effect.
Mixing different types of lamps in a?
ASTM G and G Explained | Element
The apparatus described in Practice G 53 is covered by this practice. These conditions are provided for reference only. The particular application determines which lamp should be used. Frequently, the irradiance is not controlled in this type of exposure device. This website uses cookies to improve user experience. Link to Active This link will always route to the current Active version of the standard. By using our website you consent to all cookies in accordance with our Cookie Policy.
Xenon Arc Testing Weatherometers used in the G and G tests approximate performance via intense exposure to the damaging elements in sunlight. Use of this equation requires that each spectral interval must be the same for example, 2 awtm throughout the spectral region used.
E Previous versions of this standard used window glass? Exposures are not intended to simulate the deterioration caused by localized weather phenomena, such as atmospheric pollution, biological attack, and saltwater exposure.
The minimum and maximum data are at least the three sigma limits from the mean for asstm measurements. Costs for weatherization testing will vary according to a number of factors, including moisturization, sample size, number of cycles, and more.