This standard is issued under the fixed designation D ; the 1 These test methods are under the jurisdiction of ASTM Committee D13 on. Buy ASTM D Standard Test Methods for Strength Tests for Zippers from SAI Global. ASTM D Standard Test Methods for Strength Tests for Zippers.
| Author: | Brashakar Tugal |
| Country: | Syria |
| Language: | English (Spanish) |
| Genre: | Automotive |
| Published (Last): | 17 March 2015 |
| Pages: | 90 |
| PDF File Size: | 6.80 Mb |
| ePub File Size: | 20.76 Mb |
| ISBN: | 678-6-42791-638-8 |
| Downloads: | 66248 |
| Price: | Free* [*Free Regsitration Required] |
| Uploader: | Kazikus |
The lower platen shall have attached to its entire surface a piece of neoprene rubber 6 mm 1?
Usually we quote within 12 hours after we get your enquiry. What is the payement terms? Test modular design, open data management, can realize load, deformation, displacement, variable speed control.
Apply a compression force at a rate-of-traverse of approximately 13 mm 1?
A asrm epsilon e indicates an editorial change since the last revision or reapproval. Contact Supplier Start Order. Test modular design, open data management, can realize load, deformation, displacement, variable speed control 7.
Dimension 1 and 2 A 2.
ASTM D – 07() Standard Test Methods for Strength Tests for Zippers
In cases were the puller cannot be inserted due to its thickness, such as a rubber puller, eliminate the rubber for easy gripping. The slider ast, be held? Strength of Chains and Elements. Position the trunnions midway in the length of the bails which are of the elongated type.
ASTM D2061 Zipper strength Testing Equipment
Supplier Assessed videos Factory inspection reports Xstm production lines. When a reliable estimate of v for the users laboratory becomes available, Eq 1 will usually specify fewer than the number of specimens shown in Table 1.
China farm machinery equipment China 2d061 product China washing machine equipment. Read the dial and record the amount of permanent twist. This number of specimens is calculated using values of v which are somewhat larger values of v than are usually found in practice.
ASTM D – 93() Standard Test Methods for Strength Tests for Zippers
Then seat the separable pin on the? Leave a Reply Cancel reply Your email address will not be published. High precision import weighing sensor 3. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.
If preferred, the use of a CRT tensile testing machine is permitted. In one procedure the force is applied to the mouth of the slider. Apply an initial load of 1 lb and set the dial to zero. Examine each specimen to determine whether satm not there remains the usual ease of manual movement of the pull. The X-ray fluorescence analyzer is mainly used for screening the content of chemical elements in the semi-finished products, finished zippers and certain raw materials, including lead, cadmium, chromium, mercury, arsenic, barium, antimony and selenium as well as analyzing the unknown components in the samples.
Secure the stringer in the lower clamp of the testing machine in asym alignment, positioning the clamps approximately 76 mm 3 in. Test cycles cycles.
Key Testing Facilities
Have a question about conducting the test for this standard? Other materials with established test values may be used for this purpose. Preconditioning is not required for zippers other than those made of nylon.
Secure the two stringers atm the lower clamp of the testing machine as illustrated in Fig. You may use these HTML tags and attributes: With beam displacement limit protection, force overload protection, voltage overload protection, overheating protection 8.
From both stringers remove the elements adjacent to but not under the bottom stop for a distance of d201 13 mm 1? The tape and bead may be cut either partially or completely across as long as the element to be tested is not hindered in its movement along the bead. In addition for all passing results that reach the required breaking force in both directions after 10 s the ultimate breaking force may asrm be recorded. The platens shall be hardened steel, 51 by 51 by 25 mm 2 by 2 by 1 in.
Read and record measurement of the de? Test conditions All tests are carried out at room temperature. They can be used as aids in the evaluation of zippers without the need for a thorough knowledge of zippers.
High speed, low vibration, high resolution digital closed loop controller for Japanese Panasonic AC servo drive. Originally approved in