PIC16FA Datasheet, PIC16FA Flash pin 14kB Microcontroller with A/D Datasheet and Technical Data. PIC 16FA is a microcontroller manufactured by Microchip Inc. You can see its specifications and download the datasheet here. Microchip 16FA 8-bit Microcontrollers – MCU are available at Mouser Electronics. Mouser offers inventory, pricing, & datasheets for Microchip 16FA 8-bit.
|Genre:||Health and Food|
|Published (Last):||11 April 2004|
|PDF File Size:||4.59 Mb|
|ePub File Size:||16.60 Mb|
|Price:||Free* [*Free Regsitration Required]|
Information contained in this publication regarding device applications and the like is intended through suggestion only and may be superseded by updates. Higher order bits are from the Status register. To write program data, it must first be loaded into the buffer registers see Figure EECON2 is not a physical register. For borrow, the polarity is reversed.
This buffer is a Schmitt Trigger input when used in Serial Programming mode or in-circuit debugger. EEIF must be cleared by software. Shop Test Equipment Accessories. Shop Emitters and Detectors. Shop Rectangular Lead Acid Batteries.
There darasheet six SFRs used to read and write this memory: This interrupt-on-mismatch feature, together with software configurable pull-ups on these four pins, allow easy interface to a keypad and make it possible for wake-up on key depression. Connector and Crimp Tooling. Parallel Slave Port data. The last character of the literature number is the version number, e.
Based on a powerful RISC core, these families feature a common architecture for easy migration from 6 to pins with little or no code change required. Write control for Parallel Slave Port. Read control for Parallel Slave Port. When clear, as it is when reset, any subsequent operations will operate on the data memory.
To protect against spurious writes, various mechanisms have been built-in. Oscillator crystal input or external clock source input.
Execute the special five instruction sequence: These registers are implemented as static RAM. The Reference Manual should be considered a complementary document to this data sheet and is highly recommended reading for a better understanding of the device architecture and operation of the peripheral modules. Low-voltage single-supply ICSP programming enable pin. Then the user must follow a specific write sequence to initiate the write for each byte.
Shop Power Transfer Switches.
16FA Datasheet, PDF – Alldatasheet
Chrome Firefox Edge Internet Explorer RB4 pins changed state; a mismatch condition will continue to set the bit. Then the sequence of events to transfer data to the buffer registers must be executed.
If you have any questions or comments regarding this publication, please contact the Marketing Communications Department via E-mail at docerrors mail. Basic Snap Action Switches.
DSB Note the following details of the code protection feature on Microchip devices: View More Microchip Technology Inc. These pins should be left unconnected.
Then the following sequence of events must be executed: The available features are summarized in Table Rectangular Lead Acid Batteries.
Most Current Data Sheet To obtain the most up-to-date version of this data sheet, please register at our Worldwide Web site at: Enable interrupts if using interrupts. Datsheet stack space is not part of either program or data space and the stack pointer is not readable or writable. The lower locations of each bank are reserved for the Special Function Registers. All of these features provide the Mid-Range microcontrollers with an intelligence level not previously available because of cost or size considerations.
The PIE1 register contains 16f8766a individual enable bits for the peripheral interrupts. No licenses are conveyed, implicitly or otherwise, under any intellectual property rights. When doing a table read using a computed GOTO method, care should be exercised if the table location crosses a PCL memory boundary each byte block. The C and DC bits operate as a borrow and digit borrow bit, respectively, in subtraction.
For register file map detail, see Figure When program memory is code-protected, the microcontroller can read and write to program memory normally, as well as execute instructions. The user must follow the same specific sequence to initiate the write for each word in the program block, writing each program word in sequence 00,01,10, The low byte comes from the PCL register which is a readable and writable register.