General Dwelling Calculation Method (NEC ). By Warren Goodrich. General If 3 or less appliances, then enter at percent. If there are four, or more. Receptáculos y clavijas según NEC Today’s NEC® Page i TABLE OF CONTENTS SECTION DESCRIPTION PAGE Article Defines. NEC Article Definitions, defines Authority Having Jurisdiction as “The organization, office, or individual responsible for approving equipment, materials, .
| Author: | Kazik Nizil |
| Country: | Somalia |
| Language: | English (Spanish) |
| Genre: | Literature |
| Published (Last): | 15 September 2015 |
| Pages: | 69 |
| PDF File Size: | 6.62 Mb |
| ePub File Size: | 18.16 Mb |
| ISBN: | 249-6-91658-691-9 |
| Downloads: | 35773 |
| Price: | Free* [*Free Regsitration Required] |
| Uploader: | Meziran |
If you are using this temporary on a residential application, you may size your feeders by NEC Table The following feeders are accepted practice to use in ned2002 application to serve as a service entrance conductor serving an overhead temporary, but this list does not name all conductors approved for this application.
Accepted practice will lead you to Sch 40 PVC due to a cost factor. Do not add the first 3 steps to this general lighting demand factor. We must then make one more comparison to ensure our calculated neutral service rated conductor size in wire gauge is not smaller than the minimum grounding electrode conductor size as required in NEC Article Keep in mind that the chart in NEC Article Then refer to nec article Some Utility companies will furnish that meter base nwc2002 your jec2002.
One example of an overhead temporary service may be viewed by clicking on the picture icon to the left. D 10 awg or smaller conductors. You can usually resolve this offset condition where the holes don’ t line up, by using an offset nipple. Some Utility companies require you to furnish your meter base.
General Dwelling Calculation Method (NEC ) – Self Help and More
You must supply a set of feeders approved for a wet location, and sized by the maximum amp rating of the main disconnect s used on the pole and able to reach at least 3′ past the weatherhead into free air for the Utility Company’ s connection. You must support the pipe with straps. If you use a type service panel with only two circuits in the box, you must use a minimum rating of 30 amps, weatherproof service rated panel. The minimum size wire to your receptacles, through your offset nipple, from your over-current device [breaker or fuse], is 14 awg using a 15 amp maximum size overcurrent device.
If your service panel main over-current device size is amps in a residential setting, you must use a feeder rated no less than a amp rated conductor, from the transformer, through to the main lugs of the service panel, or the lug of your main over-current device depending on the service rated panel style that you plan to use.
Absolute minimum grounding electrode conductor size is a 8 copper for amp or less and 6 copper for more than amp.
If the branch circuit nwc2002 direct connected, at the end of line, without any receptacle installed on that circuit, then no GFCI protective device is required.
The following requirements will not be found in the NEC, but these requirements will most likely be required by either the Utility Company rules, or the Authority Having Jurisdiction.
In comparing for the best deal between the two NEC tables I will attempt to approach the majority of your choices. Your overcurrent device [breaker box or fuse box] can be of an array of sizes, each size creating new requirements.
General Dwelling Calculation Method (NEC 2002)
This weathershield might be clear or opaque. Please keep in mind that any equipment being utilized as a service panel must be service rated as listed and labeled on that service rated panel’ s label.
The article is for informational purposes only and is not a substitute for professional advice. NEC Appendix Nc2002 9. List fastened-in-place appliance, and total the va. When you come out of the bottom of the disconnect or panel, you will find your bossed [treaded] receptacle box conduit 1000, laying offset from the hole at the bottom of your disconnect or panel box.
The temporary wiring style running from the temporary on the load side of the overcurrent device is rather forgiving on a temporary wiring condition. If we compare that grounding electrode conductor minimum size required to our minimum neutral main service conductor size of 4 awg copper or 2 awg aluminum we find that we are meeting the requirement in NEC Article If installing a grounding electrode conductor to a made electrode the maximum grounding electrode conductor size required is a 6 awg copper conductor NEC Article If 3 or less appliances, then enter at percent.
We must size our grounding electrode conductor by NEC Table This will be your starting point from here. Search for great deals on electrical from local home improvement companies nex2002 contractors. In this application you must use a conductor approved for a wet location, and approved as a service conductor [with a “W” in it’s identification and sunlight resistant] NEC Article Your Utility Company will flag the area where they plan to set your transformer and provide the maximum distance allowed for your overhead temporary from the Utility pole and you overhead temporary Your Utility Company will furnish your transformer for you.
The previous rules applies if the box is with equipment 1000 such as the box connected by an equipment grounding conductor to a green grounding screw NEC Article If you are using this temporary on a non-residential unit you must size your feeder by NEC Table B includes 40 and 50 amp receptacles or even volt receptacles if not part of a permanent wiring system of a permanent structure.
Find the largest motor involved, and multiply that motor’s full load current flc by 25 percent, and enter that figure. If we divided that 18, volt amps by the 100 voltage serving that dwelling of volts we should find that your minimum neutral service conductor size must be at least with an ampacity of 76 amps.
Some Utility companies will even furnish the entire temporary and electricity for one set fee.
A and NEC Article You must then run the grounding electrode conductor up the pole to the service panel. Please keep in mind, that if you use a single main overcurrent device smaller than the maximum rating of your service panel, you may reduce the feeder size to equal your main overcurrent device maximum rating, but you must provide ampacity of that service conductor equal to the maximum demand load to the equipment to be used.
This use of NEC Table All boxes on an overhead temporary service pole will be considered exposed to wet location. An example of a plastic bushing installed as required for 4 awg or larger conductors in a conduit may be viewed by clicking on the picture icon to the left. The article is for informational purposes only and is not a substitute for professional advice.
If only one dryer is used. To view an example of the inside wiring of a main service rated panel or disconnect you may view by clicking on the picture icon to the left. To view an example of a weatherproof device box and a weather shieldclick onthe picture icon to the left.
Suggested Wiring Procedures for an Overhead Temporary Service Pole (NEC 2002)
Add from here down when finding nsc2002 total demand load of the dwelling. If your service panel main over-current device size is 15 amps, you may use a feeder rated no less than a 15 amp rated conductor, from the transformer, through to the main lugs of the service panel, or the lug of your main over-current device depending on the service rated panel style that you plan to use. Find Local Contractor Call: